This profile has been claimed by the business owner or representative.
Zodiac MX6 Suction Side Pool Cleaner
About this business
Sorry, but it didn’t work for me :( Used inground pool. Only lasted one season. Expensive piece of junk. Don’t waste your money and mind. Buy something else, you’ll thank me later.
Business response:
Hi Lee, We're sorry you're experiencing issues with your Zodiac MX6 Suction Side Pool Cleaner. It definitely should last longer than one season! Please email us your phone number at feedback@zodiac.com so we can connect you with a product specialist who can help. Thank you for your patience. Regards, Zodiac, a Fluidra Company Manufacturer of Jandy, Polaris, and Zodiac products
I don't recommend the MX6 pool vac (1/4 of a star) After installing the MX6 pool cleaner it ran for about an hour and stopped. The suction was working and there was no debris in the vacuum. I shook the vac and it started working again...for about 2 hrs and stopped again with only one side of the tread touching the pool floor. I turned the pump off and set it back to the normal run schedule, hoping that it would start working when the pumped turned back on. The next morning the pump was running, the skimmers were working and ... read more
Business response:
Hi Carol, We're sorry you're experiencing issues with your Zodiac MX6 Suction Side Pool Cleaner. Here are some tips you can try: 1. Confirm that the main drain is closed. 2. Check wheel speed to verify proper flow. Refer to section, "Check for Proper Flow" in the Owner's Manual. 3. Check to see if any interior teeth of the tracks are worn. If so, contact your dealer for replacement tracks. 4. Backwash filter and empty pump basket. 5. Check for debris jammed in engine. Refer to section, "Remove Debris from Engine" in the Owne... read more
Not good for curved pool edges/walls Its good vacuum if your pool walls are straight. Unfortunately most pools have some degrees of curves on the corners in the pool. This vacuum does not know how to detach it from the curves, it gets stuck and wont move anywhere once it hits any of the curves. This is a bad design. What's the point to have a vacuum stay at one place and you have to constantly go and move it each time it does that. Returning it back!
Business response:
Hi Adam, Thanks for the review of your Zodiac MX6 Suction Side Pool Cleaner. We'd like to help you with the wall climbing issue if you still have the unit. First, verify proper flow by counting the wheel rotations of the cleaner tracks. Next, ensure the hose float is positioned approximately 9" from the cleaner. For more detailed instructions, refer to the product manual, found here: https://www.zodiacpoolsystems.com:443/en/products/suction/mx6. If you continue to need assistance, please email us your phone number at feedbac... read more
Not recommended Bad design, needs around 3000 rpm to make the robot move.
Business response:
Hi, Thanks for your feedback. Sorry about the slow performance of your Zodiac MX6 Suction Side Pool Cleaner. Here are some suggestions: 1) Ensure the main drain is closed. 2) Check the wheel speed to verify proper flow. 3) Check for track wear. 4) Backwash the pool filter and empty the pump basket. 5) Check for jammed debris in the cleaner engine. 6) Check for air in the system. 7) Ensure the flow regulator valve moves freely. For more details on these adjustments, please refer to the FAQ section and the product manual locat... read more
does a good job on the pool bottom bought to clean the pool bottom; does a good job; does get hung up some on the steps and takes a while to turn itself around and move somewhere else; reliable; I would buy this again.
Business response:
Thanks for sharing your story, Richard! As for your issue with the steps, check three things: 1) Test for proper flow. 2) Ensure correct hose length and shorten if necessary. 3) Verify that the swivel on top of the cleaner rotates freely. For more details about these adjustments and additional resources, visit https://www.zodiacpoolsystems.com/en/products/suction/mx6. If you need further assistance, please call (800) 822-7933 or email your contact info to feedback@zodiac.com. We hope these tips help. Thanks again for your fe... read more
Great replacement Great replacement for our balky Haywood model. Cleans efficiently and easy to balance
Business response:
Thanks for choosing the Zodiac MX6 Suction Side Pool Cleaner, William! Your trust and satisfaction are our top priorities. Swim on, - Zodiac, a Fluidra Company
Keep stopping Keep stopping every 30min, had was too take it out the pool and spind the weel to restart every time it stop
Business response:
Hi Ian, We're sorry you're experiencing issues with your Zodiac MX6 Suction Side Pool Cleaner. Please email us your phone number at feedback@zodiac.com so we can connect you with a product specialist who can help. Thank you for your patience. Regards, Zodiac, a Fluidra Company Manufacturer of Jandy, Polaris, and Zodiac products
It was cheap and does a cheap job. Not worth the money This is not a good pool cleaner. Unless you have the other suction ports closed or partially close at the pump, the creeper has a difficult time staying flat on the pool surface. It will roll around the pool in a 45 degree angle sucking water but nothing off the bottom until you push it down to grab hold of the pool surface. If you have a really strong pump it may do better. But I do have the right pump for my pump and just fine with my old Hayward unit. It also tends to... read more
Don’t work lose time and money Don’t lose you money in this equipment go stuck all t time ...
Frequently asked questions about Zodiac MX6 Suction Side Pool Cleaner
How is Zodiac MX6 Suction Side Pool Cleaner rated?
Zodiac MX6 Suction Side Pool Cleaner has a 3.7 star rating with 3,728 reviews.
When is Zodiac MX6 Suction Side Pool Cleaner open?
Zodiac MX6 Suction Side Pool Cleaner is closed now. It will open tomorrow at 9:00 a.m.